Do you use solid copper or copper-clad aluminum (CCA) cable?

We strictly install 100% solid bare copper cable that meets all TIA/EIA standards and UL listings. We never use Copper-Clad Aluminum (CCA) because it causes significant voltage drop for PoE devices, fails certification, and is non-compliant with commercial building codes.

Will our new cabling support Power over Ethernet (PoE)?

Yes. Our Cat6 and Cat6A solid copper installations are fully capable of pushing maximum PoE++ wattage safely to devices like WiFi access points, PTZ cameras, and VoIP phones without dangerous heat buildup.

Do you provide testing and certification reports?

Absolutely. Every single data drop we pull is rigorously tested and certified using calibrated enterprise network testers. We verify wire maps, length, near-end crosstalk (NEXT), and insertion loss, providing you with documentation proving the network is flawless.

Are your cables plenum-rated for drop ceilings?

Yes. When routing cable through spaces used for environmental air return—such as drop ceilings in most commercial offices—we use CMP (Plenum) rated cable with fire-retardant jackets to strictly comply with NEC life safety codes.

Do you clean up old, messy network racks?

Yes, MDF and IDF closet remediation is one of our specialties. We can remove abandoned wiring, install proper cable management trays, patch panels, and dramatically clean up your racks so your IT team can easily trace and service connections.

Professional structured cabling installation with cleanly dressed Cat6 wire bundles

Back to Services

Service Focus

Structured Cabling

The physical foundation everything else rides on — cameras, phones, Wi-Fi, and door controllers. We install, dress, and certify low-voltage infrastructure to standard.

Request a Free Quote

(405) 960-4633

Capabilities

Engineered Pathways

From pulling the first wire to punching down the final keystone jack, we deliver clean, reliable physical layer infrastructure.

Copper Cabling

Professional installation of Cat6 and Cat6a drops for robust gigabit and multi-gigabit throughput.

Fiber Backbone

Single-mode and multi-mode fiber optic backbone installation to bridge network switches and distant IDF closets.

Rack & Cabinet Builds

Meticulous build-outs of equipment racks, network cabinets, patch panels, and vertical cable managers.

Certification & Labeling

Rigorous certification testing for every installed drop, mapped cleanly to digital documentation and logical physical labels.

PoE & Device Low-Voltage

Structured runs correctly sized for Power-over-Ethernet devices like IP cameras, WAPs, and door controllers.

Cleanup & Remediation

Auditing, toning, re-terminating, and re-dressing failing or 'spaghetti' wiring in existing neglected data closets.

Material Standards

Solid Copper, Not Copper-Clad

The quality of the cable you install determines the reliability of the entire network. We refuse to compromise on the physical medium that carries your data and power.

Macro view of bare copper conductors vs copper clad aluminum

What We Install: Solid Bare Copper Cat6

Full compliance with TIA-568 standards and UL/ETL listings.
Lower DC resistance allows full-length PoE runs to power cameras, WAPs, and door controllers without voltage drop or heat buildup.
Stable performance supporting gigabit speeds up to the full 100m/328ft channel length.
Ductile copper conductors terminate cleanly and survive re-termination.
Required for code-compliant and warrantable commercial installations.

What Cheap Installers Use: CCA

Aluminum core with only a thin copper plating.
Roughly 40% higher resistance causes voltage drop, leading to PoE devices that randomly reboot or run dangerously hot.
Aluminum work-hardens and snaps easily at terminations, or oxidizes into intermittent faults at punch-downs and jacks.
Usually not UL-listed or NEC-compliant, instantly voiding equipment and cabling warranties.
Fails rigorous certification testing; cheap up front but expensive to rip out and replace later.

The cable is the one part of the installation you can't upgrade later without opening walls and ceilings. That's why we never cut corners on copper.

Fire Code Compliance

Riser vs. Plenum: Using the Right Jacket

Cable jackets aren't just about durability—they're life-safety components regulated by the National Electrical Code.

CMR / Riser-Rated

Designed for vertical runs between floors, risers, shafts, conduit, and general in-wall/non-air-handling areas.

Flame-retardant properties ensure fire won't travel floor to floor via the cable pathways.
Less expensive than plenum.
The correct and compliant choice strictly where no environmental air is handled.

CMP / Plenum-Rated

Required by NEC Article 800 in plenum spaces — the air-handling space above drop ceilings or under raised floors used for HVAC return.

Constructed with a low-smoke, low-toxicity fluoropolymer (FEP) jacket.
Prevents the release of dense, toxic smoke that would be distributed throughout the building by the HVAC system during a fire.
Higher upfront cost, but it is a strict code requirement, not an optional upgrade.

Plenum ceiling space with HVAC returns and cable trays

Important Note: Plenum can substitute for riser, but riser can never be used in a plenum space. We verify with building mechanical drawings or inspectors to determine which spaces are plenum. Using riser cable in a plenum ceiling is one of the most common failed-inspection and liability issues we get called in to fix.

Technician using an enterprise network tester to certify low-voltage cable drops

Testing, Certification & Handoff

Every single cable we drop undergoes rigorous certification testing using calibrated enterprise testers. We verify wire map, check total length, and measure critical interference metrics like insertion loss, NEXT (Near-End Crosstalk), and return loss. Both ends are clearly labeled according to logical physical schemas, and we hand over complete digital documentation so your IT team knows exactly where every connection goes.

Meticulously dressed commercial network cabinet with clean organized cable pathways

Craftsmanship in Pathways

A network closet shouldn't look like a spaghetti factory. We take pride in clean rack and pathway workmanship—meticulously dressing bundles, maintaining proper bend radiuses, and utilizing J-hooks and cable trays so cables never rest on ceiling tiles or ductwork. By maintaining strict separation from electrical lines and structuring racks thoughtfully, we ensure that future service, moves, and additions are fast and cost-effective.